Ethyl benzyl ether via Williamson ether synthesis

Ethyl benzyl ether, or a-ethoxytoluene is an ether used in perfumes and as a flavoring. It also finds limited use in organic synthesis. At room temperature, ethyl benzyl ether exists as a high boiling colourless oily liquid with a pleasant fruity smell reminiscent of pineapple. I have no use for ethyl benzyl ether and only made it because I wanted to try making some kind of ether.

The easiest route to the compound is the famous williamson ether synthesis which involves the SN2 reaction between an alkoxide anion and an alkyl halide. For ethyl benzyl ether, ethoxide and a benzyl halide are used. Here is what I did.

To a two necked round bottom flask, I added 32ml of ethanol (reactant and solvent). I then attached a water circulated liebig condenser to the middle neck. Through the side neck, I added in 1.5g (0.216 moles) of lithium metal granules, then sealed the side neck with a stopper. The lithium began gently bubbling in the ethanol and slowly developed a white crust on the outside. To help the lithium react, I began refluxing the mixture. Lots of white precipitate began forming as the lithium was consumed. This should be lithium ethoxide, our nucleophile for the reaction. Once almost all the lithium had reacted and all that remained was one small piece, I added in 28ml (0.243 moles) benzyl chloride (our electrophile for the reaction) through the condenser and continued refluxing for 2 hours. With addition of the benzyl chloride, the lithium ethoxide dissolved and the mixture became yellow, and upon further reflux, orange. A fine white precipitate slowly built up during the reflux, even to a point where the mixture became noticeably viscous. This precipitate should be lithium chloride, the by-product of the reaction which is insoluble in ethanol. After, reflux, I allowed the mixture to cool to room temperature, then filtered it to remove lithium chloride. I then transferred the orange filtrate to a 250ml separatory funnel (stopcock closed), washing the round-bottom and filter flask out with 15ml of ethanol then transferring this also to the separatory funnel. I added in 50ml of water, then capped, shaked and vented the separatory funnel and allowed the layers to separate which took a while since an emulsion had formed. I drained off the aqueous phase, then washed the orange organic phase again with 50ml of water. After draining the lower aqueous phase off again, I transferred the still orange organic phase to a two necked 500ml round-bottom flask containing anhydrous calcium chloride. The calcium chloride unexpectedly dissolved into the water present and formed a small bottom layer. I sealed the side neck of the flask with a stopper and set the middle neck up for simple distillation.

 The first fraction to come over was a small amount of water carrying some ethyl benzyl ether at 92-102 C. The fraction boiling between 185-190 C was collected in a storage vial. This is the ethyl benzyl ether. After distillation, I discovered that quite a substantial amount of the ethyl benzyl ether had been steam distilled over with the water in the lower fraction. So, I separated off the upper ethyl benzyl ether layer and performed another distillation, again collecting the fraction boiling at 185-190 C. This was then combined with the earlier collected product in the vial. Finally I added some anhydrous calcium chloride to the vial to dry the product. In the end, I got 16ml of dry ethyl benzyl ether as a colourless oily liquid with a strong citrus-pineapple smell. This works out to a reasonable 52% yield.

The density of the product was 0.914/cm³ which is quite close to the established value of 0.938g/cm³ suggesting relative purity. However, there is probably some unreacted benzyl chloride present, as I made computation error and accedently used an excess of benzyl chloride.

The lithium metal first reacts with the ethanol, irreversibly generating the ethoxide anion which is a powerful nucleophile. The ethoxide then undergoes a SN2 reaction with the benzyl chloride which is electrophilic producing ethyl benzyl ether.

2 Li + 2 C2H5OH ==> 2 LiC2H5O + H2

LiC2H5O <==> Li (+) + C2H5O (-)

C6H5CH2Cl + C2H5O (-) ==> C6H5C(+)H2(C2H5O)Cl

C6H5C(+)H2(C2H5O)Cl ==> C6H5CH2OC2H5 + Cl (-)

Li (+) + Cl(-) ==> LiCl

Benzyl chloride via nucleophilic substitution

Some time ago, I made some benzyl chloride by the halogenation of toluene (link). The process was on the whole quite unpleasant, very long and gave a miserable yield. It is the primary industrial method for producing benzyl chloride. I deciding to try the more common laboratory method, which is much better suited to small scale operations. Benzyl chloride is the only chlorinated organic compound produced, so the product is generally more pure, in addition the procedure is relatively short.

As a warning, benzyl chloride is highly toxic, lacrymatory, corrosive and potentially carcinogenic. This procedure should only be attempted by an experienced chemist with a good respirator in a well ventilated area. All contact should be avoided.

To a 1000ml flat-bottom boiling flask, I added 575ml of 33% hydrochloric acid. I then slowly added 78ml of benzyl alcohol while swirling the flask slightly. Once addition of the alcohol was complete, I attached a cold water circulated condenser to the flask, with one end of a tube sealed to the end of the condenser. The other end of the tube was suspended just above some sodium hydroxide solution in a separate vessel. This serves as a gas scrubber to neutralize the hydrogen chloride gas that escapes the system. Anyway, I then refluxed the mixture for 10 minutes. Even before the reflux began, an upper layer of clear liquid had separated from the rest of the liquid in the flask.  Throughout reflux, the reaction flask was frequently swirled until the layers merged. After reflux, I allowed everything to cool to near room temperature with the help of an icebath. During this time the layers had completely separated out into a cloudy lower aqueous phase and a clear organic upper phase. The organic phase should be mostly benzyl chloride with some dissolved benzyl alcohol. Anyway, I then poured as much of the mixture into a 250ml separatory funnel as could fit and drained off the lower aqueous layer. The rest of the mixture was added to the separatory funnel in portions, draining off the lower aqueous waste teach time until nothing but the entirety of the organic benzyl chloride layer was left in the funnel. The benzyl chloride was then washed with two 50ml portions of saturated sodium bicarbonate solution in succession, stoppering, shaking, and venting the separatory funnel each time. Note that for these washes, benzyl chloride forms the bottom layer. I then washed the benzyl chloride one last time with 100ml of saturated sodium chloride solution for which, the benzyl chloride formed the upper layer. After draining off the aqueous layer and discarding it, I drained off the benzyl chloride into a 200ml conical flask and dried it over anhydrous calcium chloride.

I then poured the benzyl chloride into a 500ml round-bottom flask and setup for simple distillation. The fraction boiling at 170-182 C was collected. This should be relatively pure benzyl chloride. I then dried the product again over anhydrous calcium chloride and transferred it to an amber glass bottle containing 3A molecular sieves for storage. I got 50ml of benzyl chloride which works out to a respectable yield of 58%. The product was also quite pure with a density of 1.06/cm3!

The reaction is a nucleophilic substitution, which unusually can proceed via SN1 and SN2 mechanisms. Substitution with primary alcohols (of which benzyl alcohol is one) almost exclusively proceed via SN2. This is because the carbocation intermediate involved in SN1 is much less stable for primary alkyls than it is for secondary or tertiary. However there is another factor that can come into play called resonance. Resonance allows the positive charge of carbocations to be slightly spread out across the whole molecule, and thus increase the stability. The aromatic ring in benzyl alcohol creates resonance and so the carbocation that would form in an SN1 reaction is more stable. This is why substitution with benzyl alcohol progresses via both SN1 and SN2.

SN1

HCl <==> H (+) + Cl (-)

C6H5CH2OH + H (+) ==> C6H5CH2O(+)H2

C6H5CH2O(+)H2 ==> C6H5C(+)H2 + H2O

C6H5C(+)H2 + Cl (-) ==> C6H5CH2Cl

SN2

HCl <==> H(+) + Cl (-)

C6H5CH2OH + Cl(-) ==> C6H5C(+)H2(OH)Cl

C6H5C(+)H2(OH)Cl ==> C6H5CH2Cl + OH (-)

OH(-) + H (+) ==> H2O